fs
Showing posts with label progress. Show all posts
Showing posts with label progress. Show all posts

Monday, February 10, 2014

I finally made some progress on the New Yankee Workshop workbench

I started the workbench build back at the beginning of the year by cutting all the 2x4s down to length.  My wife bought me a dado stack for christmas so I was good to go on the workbench.  It turns out that the dado stck will not fit with the standard insert on my tablesaw.  I was kind of expecting that but I was unable to find any other inserts for my saw on the Skil site so I decided to make my own.  I have been putting if off in favor of other projects but I finally got it done and was able to start using my dado stack.  Correction, I was able to start using 1/2" of my new dado stack.  It turns out that the arbor on my saw will only safely hold 1/2".  Its better than using a sungle blade and I was excited to finally get to use it.  I got all the dados and rabbits for the base frame cut and plan on pre-drilling, screwing, and glueing the base together tomorrow.


I measured and marked all the pieces for their rabbits and dados.

I also marked the fronts of the boards so that I could see where to cut it on the tablesaw.

My homemade insert has a little bit of play in it so I creeped up on the proper cutting depth.

Testing the depth of the cut.

The dados and rabbits for the top of the base frame are done.


I made quite a bit of sawdust and wood chips.

I made a sacrificial fence from some scrap 2x4s.

This is the rabbit for the bottom tool tray.

I had one dado to cut in the long center piece.  My homemade insert was moving around on me a little so I duct taped it down where the clip would be on the normal insert.  The design of the saw is kind of funky and there is no easy way to make a clip for that section.  I am writing an article on the insert and will explain more there.

More shots of the cut pieces.


I read the directions incorrectly and made this rabbit 3/4" too long.  I cut a new piece of 2x4 and made remade this piece.  Twice.  I got in too much of a hurry and made the rabbit and dado on the same side.  Im glad that I bought an extra 2x4 for this project.

The dados for the dogs need to be cut at a 4 degree angle so I cut a scrap 2x4 at 4 degrees on the mitre saw to use for marking all the cuts.

I marked the cutoff in the center and used it for the width marks.

I used that same block to set the proper angle on the mitre gauge for my table saw.

The slots for the dogs are not perfect but turned out better than expected.

Here is the final dry fit!

Read More..

Sunday, January 26, 2014

Slow Progress on the Candle Rack


Every fall I think the start of the school year has got to be the craziest time of the year. And every spring I change my mind. Hands down, the end of the school year is the craziest time. It seems like every minute has at least an hours worth of work to get done.

So after spending four hours of a beautiful Sunday in my stuffy classroom (the air circulation is shut off on weekends), I came home and hid in the shop for about an hour. It wasnt much, but I did make some progress on the candle rack.

First, I had to remember what I was working on - finishing the dovetails. Then I had to double check that I was working with the right parts in the right orientation. All stuff that just takes care of itself when you arent breaking your project up into tiny amounts of time spread over weeks.

I did the layout on the tops of the sides by eye. If you look closely, you can see that I changed my mind a couple of times:


After cutting the tails, I transferred the layout to the pin board, cut it out and what do you know? It went together the first time:


It was fun to see the case for the rack coming together:


Not much progress, but better than nothing. And a nice hour in the shop with something to show for it is never bad. Actually, an hour in the shop is never bad, whether there is something to show for it or not.


Read More..