Showing posts with label new. Show all posts
Showing posts with label new. Show all posts
Monday, February 10, 2014
Making A New Turning Saw Part III
It was time to refine the shape of the new saw; making it lighter both visually and physically. Most of the work was done on the shavehorse, but some work was done over at the bench vise. The tools used were: drawknife, spokeshaves, files, and a knife. The work was slow but fun.
Heres the beginning of the shaping process on the shavehorse:

I just shaped it by eye. The hardest part was not taking off too much - its addicting!

Some sections were easier to work on at the bench with the piece held in the front vise:

I ended up taking off quite a bit of stock. The areas around the mortise and the bottom of each arm I kept close to full thickness. Here are some comparison shots between the unshaped arm and the mostly finished arm:


After shaping the two arms with rounded, curving surfaces, the stretcher looked out of place with its flat surfaces and beveled edges. I decided to rework it to more closely match the arms. Heres two shots of all three pieces, with most of the shaping work complete:


And a shot of the assembled frame surrounded by the tools that have been working on the shaping:

Next up are the tension device (easy) and the blade assembly (not too hard, except I have this new idea on how to attach the rods to the knobs without using epoxy) so maybe this will be a four part post. Probably shouldnt have said that...
I finally made some progress on the New Yankee Workshop workbench
I started the workbench build back at the beginning of the year by cutting all the 2x4s down to length. My wife bought me a dado stack for christmas so I was good to go on the workbench. It turns out that the dado stck will not fit with the standard insert on my tablesaw. I was kind of expecting that but I was unable to find any other inserts for my saw on the Skil site so I decided to make my own. I have been putting if off in favor of other projects but I finally got it done and was able to start using my dado stack. Correction, I was able to start using 1/2" of my new dado stack. It turns out that the arbor on my saw will only safely hold 1/2". Its better than using a sungle blade and I was excited to finally get to use it. I got all the dados and rabbits for the base frame cut and plan on pre-drilling, screwing, and glueing the base together tomorrow.


















Read More..
I measured and marked all the pieces for their rabbits and dados.

I also marked the fronts of the boards so that I could see where to cut it on the tablesaw.

My homemade insert has a little bit of play in it so I creeped up on the proper cutting depth.

Testing the depth of the cut.

The dados and rabbits for the top of the base frame are done.


I made quite a bit of sawdust and wood chips.

I made a sacrificial fence from some scrap 2x4s.

This is the rabbit for the bottom tool tray.

I had one dado to cut in the long center piece. My homemade insert was moving around on me a little so I duct taped it down where the clip would be on the normal insert. The design of the saw is kind of funky and there is no easy way to make a clip for that section. I am writing an article on the insert and will explain more there.

More shots of the cut pieces.


I read the directions incorrectly and made this rabbit 3/4" too long. I cut a new piece of 2x4 and made remade this piece. Twice. I got in too much of a hurry and made the rabbit and dado on the same side. Im glad that I bought an extra 2x4 for this project.

The dados for the dogs need to be cut at a 4 degree angle so I cut a scrap 2x4 at 4 degrees on the mitre saw to use for marking all the cuts.

I marked the cutoff in the center and used it for the width marks.

I used that same block to set the proper angle on the mitre gauge for my table saw.

The slots for the dogs are not perfect but turned out better than expected.

Here is the final dry fit!

Tuesday, February 4, 2014
New Yankee Workshop Workbench update benchtop tray parts
I made the benchtop out of 2 pieces of 1/2" plywood laminated together, cut the tray bottom to size and got the groves cut for the tray to fit into.










Read More..
Here it is ready for some glue.

I put on a generous amount of glue, put the second piece on, put in some 1" screws in the middle and then clamped the hell out of it. I am hoping that this will make the top conform to the 2x4s underneath.


Yep, I used almost all of my clamps for this!

I cut the tray bottom down to its finish size on the table saw.

I set my dado stack for 1/2" wide and 1/4" deep.

I set the fence to cut a groove 3" from the top of the board.

The grooves have been cut!

I think that I am going to have to notch the plywood bottom for the tool tray.

I marked the notch on the plywood

and cut it out with my cordless jigsaw that I totally suck at using.

Monday, January 27, 2014
new colors
ok, so im curious about my new graphic choices .. what do you all think about the color changes? think of it like an eye test .. better or worse? would you rather i go back to the old format? please let me know by leaving a comment .. thanks .. dan...
Read More..
Sunday, January 26, 2014
My new router table
As I mentioned last week, I bought a new router table. It came in a million pieces and took me about an hour to assemble. I used it to make some chamfers on a project on Thursday and it worked like a champ! The new router is way more powerful then the one that came with the beginner table that I had previously. I have all the pieces for another thumb chair that have been sitting around my shop for about a month so I got off my butt and made all the finish cuts and then put a 1/2" round over on them using the new router table. The insert plate totally sagged and warped and all of my pieces got caught on the lip at one point or another. The difference between the 2 days? About 15 degrees hotter on the second day. That was unacceptable so I took it back to Home Depot this morning. I found a Craftsman router table with a die cast aluminum top on the Sears website on sale for $118 so I went to my nearest Sears and picked it up. They didnt have the sale price on the shelf but I told the clerk that it was cheaper on their website and they price matched it. I brought it home and started the assembly this afternoon. It had many less pieces and went together in a few minutes. It is about 6 inches shorter in length but probably half the weight. From watching Steve Ramseys YouTube channel I knew that he had a Ryobi router in a Craftsman table so I figured there would be no problems. I screwed with that thing for 20 minutes and couldnt get it to fit so it looks like I am going to take the router back tomorrow and go pick up a Craftsmen router. I signed up for the Craftsman Club while I was there and they sent me a $10 off coupon for joining so I plan on using that on the new router.


Read More..
This is the table I returned

This is the new one

Subscribe to:
Posts (Atom)