fs
Showing posts with label i. Show all posts
Showing posts with label i. Show all posts

Tuesday, February 11, 2014

If this isnt motivation to clean up the garage I dont know what is!


Warning, this post does not contain anything creative or inspiring, but hopefully it is somewhat entertaining and feel free to laugh with me :)

If you follow me on instagram @sarahmdorseydesigns you might of seen this last week. Yes, that is paint splattered in the garage on the dresser, wall and ceiling. It was actually everywhere, but I couldnt fit everything in the picture.

 The culprit.

How did it get there? As I was pulling into the garage I ran over a paint can and it exploded. EVERYWHERE. If this doesnt make you want to run out to your garage and clean up everything, I dont know what will! Why couldnt of been white?

Anyways, I spent the next few hours cleaning off the dresser. I didnt make it to the wall in time, so I decided to let it fully dry and then sand it down prior to painting.


This weekend David and I picked up a plastic shelf from Home Depot and got all of the paint off of the ground. I was previously storing it in a cabinet, but it was awkard to get in and out, so a lot of the time it got left out. Obviously.


We primed it first and then applied about 3 coats of paint.

This weekend we also made piles: to throw away, to give away, and to sell. It took all weekend and while the garage isnt beautifully organized, it will do! We are most likely moving in 6-9 months, so we dont want to invest money in organization things that we dont know will work in the next place.

It feels so good to have the garage clean! No more worries about running over paint cans!

and in other organization news, a few weeks ago we repaired my broken closet rod with gorilla glue. I folded and put away some of my clothes that I dont wear as often to lessen the load. So far so good!

Thank you for the advice on how to redo my closet! Like the garage, we didnt want to spend money on something that we arent sure will work in the next place.  

and finally, to leave you with something pretty. 


Saturday we had the most gorgeous sunset (with no filter/edits applied). The iPhone camera doesnt do it justice!

 Hope that your weekend was more fun than ours! 

So I am the only one who has run over a paint can? Probably. What is your worst painting disaster?

Read More..

Monday, February 10, 2014

Sharing the Wealth Part I

James and Jenny decided they wanted to work on some projects and I was glad to provide the shop and assistance. We’ve been having a great time of it!


Our first meeting was dinner and design. James decided to make a folding book stand and Jenny is making a necklace holder based on a shaker “key board” design. After dinner, we went out into the shop to get a little hands-on time with the tools and techniques they will be using.


Last night we were back at it, and the actual projects took flight! It was great getting to spend shop time with younger people (not that Im old or anything...) interested in learning to use handtools.


Here they are laying-out their pieces. James is using squares and a knife to mark his pine board for the chiseling and sawing that will free the two interlocking parts of his book stand. Jenny is using a marking gauge to get ready for re-thicknessing her Doug Fir with a scrub plane.





Here Jenny is scrubbing down almost to the gauge mark, and then she will finish up with a jack plane.



James is chopping and paring the hinge joints in his white pine.




And we ended up the night with Jenny doing some resawing – something she needed to do to get two parts out of one, and a small preview of James’ next step.



We had a great time, and I can’t wait until our next evening in the shop!

Read More..

I finally made some progress on the New Yankee Workshop workbench

I started the workbench build back at the beginning of the year by cutting all the 2x4s down to length.  My wife bought me a dado stack for christmas so I was good to go on the workbench.  It turns out that the dado stck will not fit with the standard insert on my tablesaw.  I was kind of expecting that but I was unable to find any other inserts for my saw on the Skil site so I decided to make my own.  I have been putting if off in favor of other projects but I finally got it done and was able to start using my dado stack.  Correction, I was able to start using 1/2" of my new dado stack.  It turns out that the arbor on my saw will only safely hold 1/2".  Its better than using a sungle blade and I was excited to finally get to use it.  I got all the dados and rabbits for the base frame cut and plan on pre-drilling, screwing, and glueing the base together tomorrow.


I measured and marked all the pieces for their rabbits and dados.

I also marked the fronts of the boards so that I could see where to cut it on the tablesaw.

My homemade insert has a little bit of play in it so I creeped up on the proper cutting depth.

Testing the depth of the cut.

The dados and rabbits for the top of the base frame are done.


I made quite a bit of sawdust and wood chips.

I made a sacrificial fence from some scrap 2x4s.

This is the rabbit for the bottom tool tray.

I had one dado to cut in the long center piece.  My homemade insert was moving around on me a little so I duct taped it down where the clip would be on the normal insert.  The design of the saw is kind of funky and there is no easy way to make a clip for that section.  I am writing an article on the insert and will explain more there.

More shots of the cut pieces.


I read the directions incorrectly and made this rabbit 3/4" too long.  I cut a new piece of 2x4 and made remade this piece.  Twice.  I got in too much of a hurry and made the rabbit and dado on the same side.  Im glad that I bought an extra 2x4 for this project.

The dados for the dogs need to be cut at a 4 degree angle so I cut a scrap 2x4 at 4 degrees on the mitre saw to use for marking all the cuts.

I marked the cutoff in the center and used it for the width marks.

I used that same block to set the proper angle on the mitre gauge for my table saw.

The slots for the dogs are not perfect but turned out better than expected.

Here is the final dry fit!

Read More..

Sunday, January 26, 2014

Upper pull out cabinet project Part I

I have been contracted to make a kitchen cabinet that will sit in an opening previously occupied by a larger cabinet that no longer fits. My customer bought a refrigerator that is taller than the original unit, and had to take out the upper cabinet to make the fridge work.
Our solution was to make a pull out cabinet with low sides, similar to a pull out tray. We decided its best to match the surrounding cabinets profiles on the face, and also match the color. Each presents its own challenges. Trying to match profiles requires having the right router knives. Ive had to buy a bit that will match the raised panel. As far as matching the color, I have found a match, and it will be close, but not exact. The existing kitchen is nearly 25 years old, so with oils, proteins, etc., from cooking all those years, as well as fading from nearby light sources, an exact match cannot be guaranteed, but it will be very close!
Here are some pictures of the space to fill, and also of the tray and door assembly. I have used a combination of box joinery and rabbit joinery on the tray. I also have a match on the three different profiles on the door, and have a sample door to compare it to. After the glue sets, I can stain, finish, and install this piece! The front "door" will be stained and finished, while the tray itself will be clear coated (similar to the surrounding cabinets).






Read More..

Friday, January 24, 2014

A Rack For Her Glue Gun Part I

This project began many months ago when my wife, a crafter, pinned this glue gun rack to one of her Pinterest boards. When I saw it I figured it would be easy to make and improve upon, so I re-pinned it to my Neat Things Carolyn Would Like Me To Build board.

The pin that started it the odyssey.
Fast forward a few weeks from my initially seeing it and after a particularly rough day at work I declared that I would need some time alone to unwind and headed to the shop. That’s when I set to building my version of the glue gun rack.


I decided that the the glue gun rack I built would be an experiment in sculpted design. Specifically, I wanted to juxtapose a rigid, rectilinear design on two (2) edges, while  creating a flowing, sculpted surface on the other two (2).

Starting on the rack.
I made the glue gun rack from some scraps of Walnut and Ebony I had on hand. As with any process, it began by milling the lumber flat and square. Then I did my basic layout.

Figuring out where things will go.
First, I glued the Ebony to a piece of Walnut to make a large billet. Then I used my Domino to make the mortises in all the pieces.

Dominos anyone?
With the joinery done, I marked out the basic shapes on each piece, and rough cut them on my band saw.

Rough shaping prior to assembly.
The final step before glue up was to recesses out for the glass tile the tip of the glue gun rests on. To do this, I used my small DeWalt trim router with an 1/8” spiral upcut bit and the plunge base. I routed freehand to within about 1/8” of the line and then cleaned up the edge with my chisels.

Next time, well glue up and begin shaping.

Dont forget about the +Modern Woodworkers Association Podcast. We talk woodworking with Guests from around the world of woodworking every other week. Subscribe to the RSS feed or iTunes today.
Read More..